$2,145.55

Invacare HomeFill Oxygen Compressor ( IOH200 ) 20.25″W x 15″H x 16″D is designed to supply pressurized oxygen to fill Invacare proprietary gas cylinders for ambulatory use while the patient receives therapeutic oxygen from an accessory oxygen concentrator. It can fill cylinders for portable use by ambulatory patients.

Home fill Compressor provides an unlimited, refillable oxygen supply, and ensures oxygen purity is always greater than 90 percent. HomeFill Oxygen Compressor Highlights Provides an unlimited, refillable oxygen supply Ensures oxygen purity is always greater than 90% Breathe from continuous flow oxygen concentrator at night.

  • The patient breathes from a continuous flow oxygen concentrator at night

SKU: 24114c5ee916 Category:

Description

Invacare HomeFill Oxygen Compressor Features

  • Patient protection ensures oxygen purity in the cylinder is always greater than 90%
  • No extra equipment needed because patients can breathe off concentrator while filling cylinders
  • Provides an unlimited refillable ambulatory oxygen supply
  • Encourages compliance with oxygen therapy as patients have no worries about running out of oxygen
  • The system is compatible with 5 liter or 10-liter concentrators and a wide variety of cylinder options (Concentrators and cylinders are not included)
  • Eliminating oxygen deliveries increases independence, convenience, and comfort
  • Allows the patient to breathe at home from a continuous flow concentrator and then use a convenient ambulatory pack when they are? out and about.?

What does the HomeFill Compressor Include?

  • Multistage compressor
  • Internal reservoir
  • Inlet fitting
  • Control electronics with an integral oxygen concentration sensor
  • Interlocking fill fitting
  • Drive motor

Note: Image is shown with a cylinder which is not included

How to use Oxygen Concentrator?

Connecting the Cylinder to the Compressor:

  1. Examine the cylinder gauge. If the cylinder pressure is less than 1500 psig, proceed to Step 2.
  2. Set the regulator flow dial on the cylinder to Off.
  3. Remove the cylinder and connector fillport covers (if present).
  4. Momentarily push Down on the outer ring (sleeve) of the connector fillport until Green dots are visible to reset the connector
  5. Grasp the cylinder in the area behind the cylinder fillport.
  6. Position the cylinder in the compressor cradle.
  7. Align the cylinder fillport with the connector fillport.
  8. Pull Up on the outer ring (sleeve) of the connector fillport while pushing Down on the cylinder to couple the cylinder fillport into the connector fillport.

Disconnecting the Cylinder from the Compressor:

  1. Press the compressor power switch to the Off (O) position.
  2. Grasp the cylinder in the area behind the cylinder fillport.
  3. With the other hand, grasp the outer ring (sleeve) of the connector fillport and push Down F.
  4. Lift up on the cylinder to remove from the connector fillport.
  5. When the cylinder fillport is disconnected from the connector fill port, release the outer ring (sleeve) of the connector fillport and use two hands to remove the cylinder from the compressor cradle.
  6. Place the fillport covers onto the connector fillport and cylinder fillport.
  7. Examine the cylinder gauge to ensure cylinder is full (needle pointing into Green area). If the cylinder is not full, perform the following:
    • Repeat Connecting the Cylinder to the Compressor
    • If cylinder is not full after second attempt to fill, contact the provider.

Turning the Compressor On and Off:

  1. Make sure the concentrator is On.
  2. Set the concentrator flow rate to the patient to 3 L/min or less for Platinum 5, XL, and Perfecto2 and 5 L/min or less for Platinum.
  3. Make sure the cylinder is connected to the compressor.
  4. Push the power switch on the control panel to the On ( I ) position.
  5. Examine the control panel. The following sequence of events should occur:
    • 0-3 minutes – The O2 Below Normal (YELLOW) light will be lit while the compressor warms up.
    • After three minutes – The Filling (GREEN) light will be on while the cylinder is filling.
    • The Full (GREEN) light will be on when the cylinder is finished filling.
  6. Remove the full cylinder.
  7. Push the power switch to the Off (O) position.

Details of HomeFill Oxygen Concentrator:

Particulars Details
Electrical Requirements 120 VAC ? 10% at 60Hz
Power Consumption 140 watts
Rated Current Input 2.0amps
Inlet Pressure Rating 14psi to 21psi
Oxygen Output (from concentrator)
5-liter Concentrator:
10-liter Concentrator:
0lpm to 3lpm (while filling cylinders)
0lpm to 5lpm (while filling cylinders)
Oxygen Input 0lpm to 2lpm
Dimensions 20.25″W x  15″H x 16″D
Weight 33 lbs
Cylinder Filling Times (average) M2: 24 minutes, ML4: 55 minutes, ML6: 75 minutes, M6: 60 minutes, M9: 159 minutes, D: 3.5 hours

 

Invacare HomeFill Warranty

1-year limited warranty on compressor, 3 year or 5000 hrs (whichever comes first) limited warranty on internal wear components (piston seals and rings, bearings, drive belts, check valves, pressure relief components and electric motor) and control panel.

THIS ITEM REQUIRES A PRESCRIPTION
If you do not have a prescription at time of purchase, a sales associate will reach out to you prior to delivery.